Previous  |  Next  >  
Product: Volume Replicator Guides   
Manual: Volume Replicator 4.1 Administrator's Guide   

VVR Event Notification

VVR provides the vrnotify utility to notify administrators of VVR specific events, such as SRL full, resynchronization complete, etc. You can receive notification for a VVR event on the Primary or Secondary node, or both the nodes in an RDS.

The vrnotify command enables you to write a script that receives VVR event notification and notifies administrators of these events through email, pager, etc. See the examples in this section to see how event notifications can also be used to keep history of various events.

If you do not specify the local_rvgname in the vrnotify command, event notification is started for all the RDSs on the local host. Use the -g option to receive event notifications for RVGs in a specific disk group.

The vrnotify command displays the VVR events until you explicitly terminate or kill the command.

To receive event notifications on the Primary or Secondary, enter the following command:


vrnotify -g diskgroup local_rvgname....
The argument local_rvgname... is a space-separated list of the names of the RVGs on the local host in the specified disk group.

The vrnotify command displays each event on a new line in the following format:


host_name:event_type:RDS_name:event message

The vrnotify command displays the following types of events:

Event Type Event Message

resync_started

Resync started on Primary RVG

resync_stopped

Resync stopped on Primary RVG

resync_paused

Resync paused on Primary RVG

lat_throttle_on

Latency throttling started

lat_throttle_off

Latency throttling stopped

lat_throttle_override

Latency throttling overridden

lat_throttle_fail

Latency throttling caused I/O failures

srlprot_throttle_on

SRL overflow protection throttling started

srlprot_throttle_off

SRL overflow protection throttling stopped

srlprot_override

SRL overflow protection overridden

srlprot_fail

SRL overflow protection caused I/O failures

srl_overflow

Replication stopped due to SRL overflow

srlprot_dcm_on

Started using DCM for SRL protection

srlprot_dcm_off

Stopped using DCM

rlk_connect

RLINK connected to remote

rlk_disconnect

RLINK disconnected from remote

srl_log_warn

SRL over 80% full

repmode_sync

Replicating in synchronous mode

repmode_async

Replicating in asynchronous mode

repibc_freeze

Replication on Secondary frozen due to IBC

repibc_unfreeze

Replication on Secondary unfrozen after IBC

rvg_pritosec

RVG role changed from Primary to Secondary

rvg_sectopri

RVG role changed from Secondary to Primary

rvg_pritoactsec

RVG role changed from Primary to acting Secondary

rvg_actsectopri 

RVG role changed from acting Secondary to Primary

rlk_paused

Secondary RLINK paused because of a configuration error

ibcmsg_discarded

IBC was discarded due to timeout on the Secondary.

Example:

The following example script shows how to use the vrnotify utility to receive event notifications for the hr_rvg RDS in the hrdg disk group and send email to the alias vvradmin if the event srl_warning occurs.


#!/bin/sh
IFS=:
vrnotify -g hrdg hr_rvg | while read host event rvg msg
do
 case $event in
 srl_log_warn)
  (echo "This message is sent by VVR notify mechanism"
   echo "SRL for RVG $rvg on host $host is 80% full"
  ) | mailx -s "VVR SRL Log Warning" vvradmin;;
 esac
done

 ^ Return to Top Previous  |  Next  >  
Product: Volume Replicator Guides  
Manual: Volume Replicator 4.1 Administrator's Guide  
VERITAS Software Corporation
www.veritas.com