Skip Headers
Oracle® Transparent Gateway for DRDA Installation and User's Guide
10g Release 2 (10.2) for Microsoft Windows

Part Number B16218-01
Go to Documentation Home
Home
Go to Book List
Book List
Go to Table of Contents
Contents
Go to Index
Index
Go to Master Index
Master Index
Go to Feedback page
Feedback

Go to previous page
Previous
Go to next page
Next
View PDF

4 Installing the Gateway

This chapter provides general information about gateway installation that is specific to this release of the Oracle Transparent Gateway for DRDA for Microsoft Windows. This chapter includes the following sections:

Introduction

The complete Oracle Transparent Gateway for DRDA for Microsoft Windows installation process is divided into installation and configuration tasks. This process is described in Chapters 4 through 8. If this is the first time the gateway has been installed on your Pentium-based host, then you must perform all the steps documented in these chapters.

The installation tasks include:

An installation checklist follows, which you can use to check off each completed step in the process.

Before You Begin

This chapter requires you to enter parameters that are unique to your system in order to properly configure the gateway. Refer to Appendix E, "Configuration Worksheet" for a worksheet listing all the installation parameters that you will need to know in order to complete the configuration process. Ask your network administrator to provide these parameters before you begin.

You will also need to confirm that all hardware and software requirements have been met. Refer to Chapter 3, "System Requirements" to verify these requirements.

Checklist for Gateway Installation

Use the following checklist for installing the gateway:

Installation Overview

The primary installation tasks are presented with the assumption that you will configure the gateway with a single Oracle integrating server and a single DRDA database. The steps for expanding the configuration to multiple integrating servers and multiple DRDA databases are described in Chapter 10, "Configuring the Gateway".

For general information about installing Oracle products and how to use the Oracle Universal Installer, refer to the Oracle Database Installation Guide for Microsoft Windows (32-Bit).

Preinstallation

ORACLE_HOME is the root directory in which Oracle software is installed.

Throughout this book, ORACLE_HOME is used to refer to the home directory of the Oracle Transparent Gateway for DRDA for Microsoft Windows, unless specifically stated otherwise.

Installing the Gateway from the Installation Media

The Oracle Universal Installer for Microsoft Windows is provided on the installation media with the gateway.

Step 1: Log on to the host

Log on to your host computer as a member of the Administrators group.

Step 2: Load the CD-ROM into the CD-ROM Drive

Use any CD-ROM drive that is attached to the Pentium-based host (either locally or as a shared resource) as a logical drive to install the gateway. If the CD-ROM drive cannot copy files to your hard disk, then refer to your CD-ROM documentation. The installation steps are presented with the assumption that the CD-ROM drive is mapped to the G: drive.

To load the gateway distribution CD-ROM:

  1. Insert the gateway distribution CD-ROM into the CD-ROM drive.

  2. Verify that the drive is assigned to the logical drive that you selected and that you can access files on the CD-ROM.

Step 3: Start the Oracle Universal Installer on Microsoft Windows

If you previously installed another Oracle Microsoft Windows product, such as an earlier version of the Oracle server or the gateway, then Oracle Universal Installer has already been set up in the Microsoft Windows program menu.

Start the Oracle Universal Installer from the Start menu rather than by using Microsoft Windows Explorer.

  1. From the Start menu, click Run.

  2. Enter the path and executable file name:

    G:\SETUP.EXE
    
    
  3. Click OK.

Step 4: Step through the Oracle Universal Installer

The Oracle Universal Installer is a menu-driven utility that guides you through installation of the gateway by prompting you with action items. The action items and the sequence in which they appear depend on your platform. Use the following table as a guide to the installation, following the instructions in the Response column.

Table 4-1 Steps to Install the Gateway Using the Oracle Universal Installer

Prompt Response

Welcome

Click Next.

Specify Home Details

Check that the destination path points to your ORACLE_HOME. Click Next.

Available Product Components

Open the Oracle Transparent Gateways product group and select Oracle Transparent Gateway for DRDA. Open the Oracle Transparent Gateway for DRDA product group, if not already open, and select one protocol from the list of supported protocols. Remove selection from everything else for a standalone gateway installation. Click Next.

DRDA Network Interface Product Software

If the SNA protocol was selected, choose the network interface software suitable for this installation of the gateway. Click Next. If the SNA protocol was not selected, this panel does not appear.

Summary

Verify the products to be installed. Click Next.


Step 5: Verify Installation Success

After the Oracle Universal Installer confirms that the installation has ended, verify that the installation was successful. To do this, check the contents of the installation log file, which is located in the C:\Program Files\Oracle\Inventory\logs directory. The default file name is InstallActionsdate.LOG.

Installation Complete

Your gateway installation is now complete. Proceed with the configuration tasks that are described in Chapters 5 through 10.

Removing the Gateway

Removing the Oracle Transparent Gateway for DRDA requires the use of the Oracle Universal Installer. Follow the procedures below to remove the gateway:

  1. To restart the Oracle Universal Installer, refer to the installation process found earlier in this chapter in "Installing the Gateway from the Installation Media", and repeat the following three steps (Steps 1, 2, and 3):

    1. Step 1: Log on to the host

    2. Step 2: Load the CD-ROM into the CD-ROM Drive

    3. Step 3: Start the Oracle Universal Installer on Microsoft Windows

  2. When the Welcome panel appears, select Advanced Installation and Click Next. Then, in the File Locations panel, click Installed Products.

  3. In the list of installed products, select the Gateway product and any other products that you wish to remove, and click Remove.