-C H A P T E R

C H A P T E R 23

System Service Processor Test (ssptest)

The ssptest exercises the Remote System Control (RSC) feature, which is integrated on the Sun Enterprise 250 as well as the next-generation RSC 2.0 plug-in card introduced with the Sun Fire 280R line, and Advanced Lights-Out Management (ALOM) feature. The ALOM feature is integrated into the Sun Fire V210, Sun Fire V240, and Sun Fire V440 systems.

The RSC or ALOM provides secure remote access for system monitoring, firmware updates, and failure recovery. The RSC or ALOM communicates with the host through two internal serial lines, the I2C bus, and reset lines.

The RSC 1.0 hardware consists of the controller, flash, SEEPROM, 10MB Ethernet port, and an external console serial port.

The RSC 2.0 plug-in card hardware consists of the controller, flash, SEEPROM, 10MB Ethernet port, FRUSEEPROM, Time of Day (ToD) device, internal PCMCIA modem card, and battery backup.

The ALOM hardware consists of a Motorola MPC850 processor, flash, SEEPROM, 10MB/100MB Ethernet Port, Time of Day (ToD) device, Serial Transceiver, and battery backup.

ssptest is not scalable.

ssptest Subtests

The ssptest will present different subtests and options based on which type of hardware (RSC or ALOM) and which version of RSC hardware (1.0 or 2.0) it is testing.

The subtests common to RSC 1.0, RSC 2.0, and ALOM include:

TABLE 23-1 Subtests for Both RSC 1.0, RSC 2.0, and ALOM
Subtest	Description
Ethernet	Allows for internal loopback testing, on the Ethernet device with user specified data, size, and number of packets.Allows for external loopback testing with user-specified data, size, and number of packets. This requires a connection to a 10MB hub or switch for RSC 1.0, or a passive loopback connector for RSC 2.0, and ALOM.Allows for a ping to be sent to a specified host and checks the response.
Flash CRC	Performs a checksum test on the flash device.
SEEPROM CRC	Performs a checksum test on the SEEPROM device.
Serial	Allows internal loopback testing with user-specified data and size on the two internal serial ports. Allows for internal and/or external testing on the external `ttyu` port. The external test requires a passive loopback connector.

ssptest also presents the following subtests when running on the RSC 2.0 hardware:

TABLE 23-2 Subtests for RSC 2.0 Only
Subtest	Description
FRU SEEPROM CRC	Performs a checksum test on the SEEPROM device.
I2C	Tests the i2c bus connection between the host and the RSC.
ToD	Performs multiple reads to the ToD device and verifies that the time is incrementing.
Modem	Verifies that the modem is installed. Displays the manufacture information, in Verbose mode. Performs AT inquiry commands.

ssptest presents the following subtests when running on the ALOM hardware:

TABLE 23-3 Subtests for ALOM Only
Subtest	Description
I2C	Tests the i2c bus connection between the host and the ALOM.
ToD	Performs multiple reads to the ToD device and verifies that the time is incrementing.

The subtests call test modlets that are written in the native Real Time Operating System (RTOS) that resides in the RSC firmware. The ssptest subtests execute the test modlets, pass parameters, and retrieve results from the RSC or ALOM using a test protocol on the host to RSC or ALOM internal serial lines.

ssptest Options

To reach the dialog box below, right-click on the test name in the System Map and select Test Parameter Options. If you do not see this test in the System Map, you might need to expand the collapsed groups, or your system may not include the device appropriate to this test. Refer to the SunVTS User's Guide for more details.

FIGURE 23-1 ssptest Test Parameter Options Dialog Box (Top Section)

Screenshot of the top section of the ssptest Test Parameter Options dialog box.

FIGURE 23-2 ssptest Test Parameter Options Dialog Box (Bottom Section)

Screenshot of the bottom section of the ssptest Test Parameter Options dialog box.

Note - The Configuration field in the ssptest Test Parameter Options dialog box displays the which type of hardware (RSC or ALOM) is being tested. For RSC 1.0 and 2.0, Remote System Control is displayed. For ALOM, Advanced Lights-Out Management is displayed.

TABLE 23-4 `ssptest` Options
`ssptest` Options	Description
Enet test	Enables or disables RSC or ALOM Ethernet testing.
Data Pattern Type	Selects Sequential, Random, or both types of data patterns.
Packet Size	Defines the size of each data packet to be sent for all tests.
Num Packets	Specifies the number of data packets to send in one test loop.
Target Host	Specifies the IP address of a host to use for the ping test.
Enet Test Type	Selects any or all Internal, External, or ping tests.
Flash test	Enables or disables the flash checksum test.
SEEPROM test	Enables or disables the SEEPROM checksum test.
FRU SEEPROM test	Enables or disables the FRU SEEPROM checksum test (RSC 2.0 only).
TOD test	Enables or disables the Time Of Day test.
I2C test	Enables or disables the I2C test (RSC 2.0 and ALOM only).
Serial test	Enables or disables the RSC or ALOM serial test.
Data Size	Defines the data size to be sent.
Loopback Type	Selects Internal, External, or both. External requires a loopback plug.
Data Pattern Type	Selects Sequential, Random, or both types of data patterns.
Serial Test Type	Selects serial ports to be tested, u to u, c to c, or d to d.
TTYU_Baud	Select a fixed baud rate or all baud rates for testing the ttyu port. The valid baud rates under TTYU_Baud are: ALL, 300, 600, 1200, 2400, 4800, 9600, 14400, 19200, 38400, 57600, 76800, 115200. The default is 9600.
Modem Test	Used to Enable or Disable the RSC PCMCIA modem test (RSC 2.0 only).

ssptest Test Modes

ssptest supports the following tests as described in the table below.

TABLE 23-5 `ssptest` Supported Test Modes
Test Mode	Description
Connection	Reports the status of the RSC or ALOM.
Exclusive	Tests the RSC's and ALOM's Ethernet, flash, SEEPROM, ToD, I2C, and serial devices. All tests use the internal modes as defaults. The `ssptest` will not run the serial test on `ttyc` if the console has been redirected to the RSC. The `ttu` tests will not run if there is an open login on the `ttyu`.

ssptest Command-Line Syntax

RSC 1.0: /opt/SUNWvts/bin/ssptest standard_arguments -o enet=E/D, epattype=seq+rand,esize=packet_size,epkts=number_packets,target=IP_address, etest=I+E+P,flash=E/D,seeprom=E/D,serial=E/D,sdatsize=data_size, slb=I+E,spattype=seq+rand,stest=u_u+c_c+d_d,ttyubaud=baud_rate|all

RSC 2.0: /opt/SUNWvts/bin/ssptest standard_arguments -o enet=E/D, epattype=seq+rand,esize=packet_size,epkts=number_packets,target=IP_address, etest=I+E+P,flash=E/D,seeprom=E/D,fruseeprom=E/D,tod=E/D, i2c=E/D,serial=E|D,sdatsize=data_size,slb=I+E,spattype=seq+rand, stest=u_u+c_c+d_d,ttyubaud=baud_rate|all,rscmodem=E/D

ALOM: /opt/SUNWvts/bin/ssptest standard_arguments -o enet=E/D, epattype=seq+rand,esize=packet_size,epkts=number_packets,target=IP_address, etest=I+E+P, flash=E/D,seeprom=E/D,tod=E/D,i2c=E/D,serial=E/D,sdatsize=data_size,slb=I, spattype=seq+rand, stest=d_d

TABLE 23-6 `ssptest` Command-Line Syntax
Argument	Description
`enet=`enable`\|`disable	Enables or disables RSC or ALOM Ethernet test.
`epattype=`seq+rand	Predefined pattern options used for Enet test.
`esize=`packet_size	Data size for each packet in the Enet test.
`epkts=`number_packets	Number of packets to send for Enet test.
`target=`IP_address	IP address of target system for Enet ping test.
`etest=`Internal`+`External+Ping	Selects any or all Internal, External, or ping tests.
`flash=`enable`\|`disable	Enables or disables RSC or ALOM Flash checksum test.
`seeprom=`enable`\|`disable	Enables or disables RSC or ALOM SEEPROM checksum test.
`fruseeprom=`E/D (RSC 2.0 ONLY)	Enables or disables RSC FRU SEEPROM checksum test.
`tod=`E/D (RSC 2.0 and ALOM ONLY)	Enables or disables RSC or ALOM Time of Day test.
`i2c=`E/D (RSC 2.0 and ALOM ONLY)	Enables or disables RSC or ALOM i2c test.
`serial=`enable`\|`disable	Enables or disables RSC or ALOM serial test.
`sdatsize=`data_size	Data size for the `rsc` or `alom` serial tests.
`slb=`Internal`+`External	Loopback type. External N/A on ports C and D.
`spattype=`seq`+`rand	Predefined pattern options used for RSC or ALOM serial test.
`stest=`u_u`+`c_c`+`d_d	Defines port and configuration to use for RSC or ALOM serial test.
`ttyu_baud=`ALL\|specific_baud	Defines baud rates to be used in testing the RSC's console port. The valid baud rates under `ttu_baud` are: ALL, 300, 600, 1200, 2400, 4800, 9600, 14400, 19200, 38400, 57600, 76800, 115200. The default is 9600.
`rscmodem=`E/D	Enables or disables the RSC PCMCIA modem test.

Note - 64-bit tests are located in the sparcv9 subdirectory: /opt/SUNWvts/bin/sparcv9/testname, or the relative path to which you installed SunVTS. If a test is not present in this directory, then it may only be available as a 32-bit test. For more information refer to the "32-Bit and 64-Bit Tests" section of the SunVTS 5.1 Test Reference Manual (816-5145-10).