-C H A P T E R

C H A P T E R 11

Alarm Card Test for Netra trademark

CT Systems (alarm2test)

The alarm2test exercises the Alarm Card and System Controller Board on the Sun Netra trademark CT 410 and CT 810 systems.

The Alarm Card is a hot-swappable add-on option for the Netra CT systems which provides secure remote access for system monitoring, failure recovery, and alarm notification. The Alarm Card can be used in both front and rear-access systems.

This test is not scalable.

Note - The Netra CT 410/810 system only runs the 64-bit OS (to take full advantage of UltraSPARCII). Although, alarm2test is available in 32-bit and 64-bit mode, only the 64-bit version of alarm2test can be performed on a Netra CT 410/810 system.

alarm2test Requirements

Solaris 9 4/03 operating environment or later is required to perform the alarm2test. Ethernet loopback and serial loopback connectors are also required to perform the alarm2test. In addition, you are required to select the Intervention mode due to the serial and Ethernet loopback connectors.

alarm2test Subtests

alarm2test consists of eight subtests which test and report on the following:

Ethernet Internal, External, PHY loopback and PING test
Internal/External loopback test on serial ports
Checksum test on FLASH
Alarm relay on/off test
System status panel LED test
Fan status test
Power supply test
FruID checksum test

alarm2test Options

To reach the dialog box below, right-click on the test name in the System Map and select Test Parameter Options. If you do not see this test in the System Map, you might need to expand the collapsed groups, or your system may not include the device appropriate to this test. Refer to the SunVTS User's Guide for more details.

FIGURE 11-1 alarm2test Test Parameter Options Dialog Box With the Scroll Bar at the Top

Screenshot of the alarmtest Test Parameter Options dialog box.

FIGURE 11-2 alarm2test Test Parameter Options Dialog Box With the Scroll Bar at the Bottom

TABLE 11-1 `alarm2test` Options
Option	Description
Enet_Test	Enables or disables Ethernet testing.
Edata_Pattern_Type	Selects the type of data pattern for `Enet_Test`: Sequential, Random, or both.
Num_Packets	Specifies the number of data packets to be sent in one test loop.
Target_IP_Addr	Specifies the IP address of a host to use for the ping test.
Etest_Type	Selects any or all internal, external, Phy (ethernet transceiver), or ping tests.
Serial_Test	Enables or disables `serial_test`.
Loopback_Type	Selects internal loopback, external loopback, or both.
Data_Pattern_Type	Selects the type of data pattern for `serial_test`: Sequential, Random, or both.
STest_Type	Selects ports to be tested: `c`, `d`, `u`, or `v`.
COM1_Baud	Selects the alarm card's COM1 port baud rate.
COM2_Baud	Selects the alarm card's COM2 port baud rate.
Flash_Test	Enables or disables the flash checksum test.
ALARMPORT	Enables or disables the alarmport test.
ALARMNUM	Selects any or all alarm ports to be tested: 0, 1, 2, 3.
ALARM0ON	Turns on, turns off, or toggles (on then off) alarm port 0.
ALARM1ON	Turns on, turns off, or toggles (on then off) alarm port 1.
ALARM2ON	Turns on, turns off, or toggles (on then off) alarm port 2.
ALARM3ON	Turns on, turns off, or toggles (on then off) alarm port 3.
FRUID_PRES	Enable/Disable FRU ID Presence test
SCB_Fpga	Enable/Disable scb_fpga register test
MidPlane_Id	Enable/Disable Midplane ID test
LEDS_ON_Continuity	Enable/Disable SCB LEDs test
Slot_LEDS	Enable/Disable Slot LEDs test
Disk_LEDS	Enable/Disable Disk LEDs test
Power_Supply_LEDS	Enable/Disable Power Supply LEDs test
Fan_LEDS	Enable/Disable Fan LED test
SCB_LEDS	Enable/Disable SCB Resgister LEDs test
FTM_LEDS	Enable/Disable Front Tranission Module LEDs test
Green_LED_Blink	Enable/Disable Green LED Blink test
FRU_Presence	Enable/Disable FRU Presence test
Health	Enable/Disable Health test
Power_Supply_ONOFF	Enable/Disable Power Supply On/Off test
Power_Supply_Status	Enable/Disable Power Suppluy Status test
Fan_Status	Enable/Disable Fan Status test
FRU ID CheckSum	Enable/Disable FRU ID Checksum test for Midplane, SCB, Alarm, Fan1/Fan2, and Power Supply1/Supply2

alarm2test Loopbacks

The loopback tests use the following external loopbacks:

Ethernet loopback test--standard RJ-45 connector. Connect pin 1 to pin 3, and pin 2 to pin 6.
Serial loopback test--RJ-45. Connect pin 6 to pin 3, pin 1 to pin 8, and pin 2 to pin 7.

alarm2test Test Modes

TABLE 11-2 `alarm2test` Supported Test Modes
Test Mode	Description
Connection	Reports the status of the alarm card.
Functional	Runs the the full set of subtests.

alarm2test Command-Line Syntax

TABLE 11-3 `alarm2test` Command-Line Syntax
Argument	Explanation
`enet=`E(nable)/D(isable)	Enables or disables Ethernet testing.
`epattype=`seq+rand	Selects the type of data pattern for `Enet_Test`: Sequential, Random, or both.
`target=`IP_Address	Specifies the IP address of a host to use for the ping test.
`etest=`Internal+External+Ping+Phy	Selects any or all internal, external, Phy (ethernet transceiver), or ping tests.
`serial=`E(nable)/D(isable)	Enables or disables `serial_test`.
`slb=`I+E	Selects internal loopback, external loopback, or both.
`spattype=`seq+rand	Selects the type of data pattern for `serial_test`: Sequential, Random, or both.
`com1baud=`ALL\| specific_baud	Defines baud rates to be used in testing the alarmcard's COM1 port.
`com2baud=`ALL\| specific_baud	Defines baud rates to be used in testing the alarmcard's COM2 port.
`flash=`E(nable)/D(isable)	Enables or disables the flash checksum test.
`aport=`[E]nable\|[D]isable	Enables or disables the alarmport test.
`anum=`0+1+2+3	Selects any or all alarm port to be tested: 0, 1, 2, 3
`a0on=`On\|Off/\|T]oggle	Turns on, turns off, or toggles (on then off) alarm port 0.
`a1on=`On\|Off\|[T]oggle	Turns on, turns off, or toggles (on then off) alarm port 1.
`a2on=`On\|Off\|[T]oggle	Turns on, turns off, or toggles (on then off) alarm port 2.
`a3on=`On\|Off\|[T]oggle	Turns on, turns off, or toggles (on then off) alarm port 3.
`FruIdPres=`E(nable)\|D(isable)	Enable/Disable FRU ID Presence test
`FpgaId=`E(nable)\|D(isable)	Enable/Disable scb_fpga register test
`MidPlaneId=`E(nable)\|D(isable)	Enable/Disable Midplane ID test
`Continuity=`E(nable)\|D(isable)	Enable/Disable SCB LEDs test
`SlotLeds=`E(nable)\|D(isable)	Enable/Disable Slot LEDs test
`DiskLeds=`E(nable)\|D(isable)	Enable/Disable Disk LEDs test
`PsupplyLeds=`E(nable)\|D(isable)	Enable/Disable Power Supply LEDs test
`FanLeds=`E(nable)\|D(isable)	Enable/Disable Fan LED test
`ScbLeds=`E(nable)\|D(isable)	Enable/Disable SCB Resgister LEDs test
`FtmLeds=`E(nable)\|D(isable)	Enable/Disable Front Tranission Module LEDs test
`GreenLedsBlink=`E(nable)\|D(isable)	Enable/Disable Green LED Blink test
`FruPresence=`E(nable)\|D(isable)	Enable/Disable FRU Presence test
`Health=`E(nable)\|D(isable)	Enable/Disable Health test
`PowerSupply=`D(isable)\|E(nable)	Enable/Disable Power Supply On/Off test
`PsupplyStatus=`E(nable)\|D(isable)	Enable/Disable Power Suppluy Status test
`FanStatus=`E(nable)\|D(isable)	Enable/Disable Fan Status test
`FruIdChkSum=`E(nable)\|D(isable)	Enable/Disable FRU ID Checksum test for Midplane, SCB, Alarm, Fan1/Fan2, and Power Supply1/Supply2

Note - 64-bit tests are located in the sparcv9 subdirectory /opt/SUNWvts/bin/sparcv9/testname, or the relative path to which you installed SunVTS. If a test is not present in this directory, then it may only be available as a 32-bit test. For more information refer to the "32-Bit and 64-Bit Tests" section of the SunVTS 5.1 Test Reference Manual (816-5145-10).